1. Core
This instruction shows how to swap the Core in a Hatch Tiled installation, where the Core is installed inside or outside of the shower area. Follow the instructions in detail, and don't hesitate to reach out if you have any questions - support@orbital-systems.com.
Use one of the kits below to swap the Core.
Core |
Filter Capsule |
or
Core Refurbished |
Filter Capsule |
Dismantle Core
Turn off the power.
Turn off the incoming hot and cold water.
Push the top left corner to tilt the door open. Lift the door off the lower brackets. Be aware that the weight of the door is 8-12 kg, depending on the tile thickness.
Caution
The weight of the Hatch Tiled door is approximately 8-12 kg, depending on the tile thickness. Be careful when lifting.
Open the door on the Core and release the Filter hatch.
Remove the Filter Capsule. Use the plugs from the Filter hatch in the new Core and transfer to the old one. The larger plug should be placed in the upper bracket, and the smaller plug in the lower one.
Close the hatch and the door.
Disconnect the shower water connection (outgoing). Then, disconnect the water connections for incoming hot and cold water. Wipe off any remaining water that drains from the pipes.
Disconnect the Wi-Fi antenna cable.
For Ethernet installation: Unscrew the protective cover and disconnect the Ethernet cable.
Disconnect the flush hose and recirculation hose from the bottom of the Core.
Disconnect the Sensor Tank and Control Dial (red and blue connector). For installations with Orbital Audio, do also disconnect the amplifier (yellow connector).
Make sure the safety wire is connected to the Core and Wall Box.
Unscrew the Core from the top vibration damper and gently lean it forward until the wire is fully extended and holds the Core.
Make sure the power is off. Then unscrew the lid of the electrical box and set it aside.
Loosen the strain relief. Disconnect the cables and pull out the power cable to the Core from the electrical box.
Wipe off the Core thoroughly. This is important to ensure a proper grip when lifting it out.
Disconnect the safety wire and lift out the Core. Put it in a safe and stable place.
Install Core
Take the new Core out of the packaging and put it in a safe and stable place. Make sure that the packaging and pallet are saved in good condition - they should be reused when returning the replaced Core. Also, save the foam inserts to ensure that the Core can be sent back in a safe and stable way.
Transfer the transport plugs from the new Core to the old one.
Place the new device in the Wall Box. The Core should click all the way into the vibration damper.
Attach the safety wire to the Core and keep it in the tilted position.
Feed the stripped part of the electrical cable into the electrical box and tighten the strain relief.
Connect the cables and screw the lid back to the electrical box.
Lean back and screw the Core onto the vibration damper. Make sure the electrical cable is placed behind the hot water pipe without any sharp bends, and make sure it is not pinched behind the Core.
Open the Filter hatch and insert a Filter Capsule.
Connect the hot and cold water connections. Then connect the shower water connection to the Core.
Caution
Make sure the gaskets are in good condition and have no damage.
Connect the Wi-Fi antenna cable.
For Ethernet installation: Unscrew the protective cover and connect the Ethernet cable.
Apply fixture grease and connect the recirculation hose and flush hose to the Core.
It is important to relubricate the plug-in coupling and hose to prevent damage to the o-ring in the connection on the Core.
Unscrew the protective caps on the red and blue communication ports on the Core. Then plug in the Control Dial (red port) and Sensor Tank (blue port).
For installations with Audio: Unscrew the protective cap on the yellow communication port and plug in the amplifier. The contacts should be tightened by hand, and the cable to the Control Dial and amplifier should be routed behind the air gap tank.
Caution
Ensure a proper alignment between the connector and the communication port. This must be done with special attention to prevent damage to the pins.
Fit the protective caps on the old Core and place it in the packaging.
Turn on the incoming water. Check and fix any water leaks. Then turn on the power. It takes about 1 minute for Core to start up.
Secure the door onto the brackets, tilt it inward to close it, and press the upper left corner to lock it in place.
Verify the shower. Follow the guide here.
The replaced Core should be sent back to Orbital.
As per the instructions, make sure the plugs and protective caps are transferred from the new to the old Core.
Use the pallet, box, and foam inserts from the new Core to pack the old Core. Secure the box safely to the pallet using straps, tape, or similar.
Record the work order number on the label if it is not already there, and contact Orbital to book the pickup.
Complete and submit the service report (found in the service request). Please make sure to include the the new Core serial number, which is located on the top of the Core.
Recycle any other components.
